{
  "kind": "synthetic-demonstration",
  "notFieldAcceptance": true,
  "product": "CADAR",
  "preparedAt": "2026-09-12",
  "project": "DEMO-ASSEMBLY",
  "projectVersion": 1,
  "planVersion": 1,
  "originalResult": "NOK with outstanding evidence",
  "reviewDecision": "pending",
  "releaseAllowed": false,
  "observations": [
    {
      "检查点 / Checkpoint": "CP-01",
      "项目 / Item": "盖板安装 / Cover installation",
      "标准 / Requirement": "按图纸方向安装 / Match drawing orientation",
      "实际 / Observation": "方向一致 / Correct orientation",
      "原始结果 / Original result": "OK",
      "证据状态 / Evidence status": "演示占位，非现场照片 / Illustration, no field photo",
      "后续处理 / Follow-up": "示例人工确认 / Illustrative human confirmation"
    },
    {
      "检查点 / Checkpoint": "CP-02",
      "项目 / Item": "螺栓数量 / Bolt count",
      "标准 / Requirement": "8 颗 / 8 bolts",
      "实际 / Observation": "6 颗，缺 2 颗 / 6 present, 2 missing",
      "原始结果 / Original result": "NOK",
      "证据状态 / Evidence status": "演示：需全貌与缺口照片 / Demo: overview and gap photo required",
      "后续处理 / Follow-up": "补装后复检 / Reinspect after correction"
    },
    {
      "检查点 / Checkpoint": "CP-03",
      "项目 / Item": "接头方向 / Connector orientation",
      "标准 / Requirement": "朝右 / Facing right",
      "实际 / Observation": "朝左 / Facing left",
      "原始结果 / Original result": "NOK",
      "证据状态 / Evidence status": "演示：需方向对照照片 / Demo: comparison photo required",
      "后续处理 / Follow-up": "纠正方向并复检 / Correct and reinspect"
    },
    {
      "检查点 / Checkpoint": "CP-04",
      "项目 / Item": "铭牌核对 / Nameplate check",
      "标准 / Requirement": "文字清晰且版本一致 / Legible, matching revision",
      "实际 / Observation": "缺少照片 / Photo missing",
      "原始结果 / Original result": "未完成 / Incomplete",
      "证据状态 / Evidence status": "未提供证据 / Evidence absent",
      "后续处理 / Follow-up": "阻止签核，补拍 / Block sign-off; capture evidence"
    }
  ],
  "workflow": [
    "Publish immutable plan version",
    "Inspect all checkpoints and upload required evidence",
    "Review against the same version",
    "Assign and claim reinspection",
    "Inspect in a new session after correction",
    "Review the new session before closing the task"
  ],
  "fieldAcceptanceChecklist": [
    {
      "item": "Device and software versions recorded",
      "status": "not-tested-on-site"
    },
    {
      "item": "CAD matches physical revision",
      "status": "not-tested-on-site"
    },
    {
      "item": "Correct / missing / wrong assembly samples authorized",
      "status": "not-tested-on-site"
    },
    {
      "item": "Repeatability and wrong-lock failures measured",
      "status": "not-tested-on-site"
    },
    {
      "item": "Lighting, distance, occlusion and temperature recorded",
      "status": "not-tested-on-site"
    },
    {
      "item": "Offline sync retains all evidence",
      "status": "not-tested-on-site"
    },
    {
      "item": "Supervisor changes and report editions agree",
      "status": "not-tested-on-site"
    },
    {
      "item": "MES idempotency and correction receipts verified",
      "status": "not-tested-on-site"
    },
    {
      "item": "OSS access and data handling verified",
      "status": "not-tested-on-site"
    }
  ],
  "note": "All values are synthetic. No customer identity, actual photo, signature or measured performance is implied."
}